TPS2320IDR

Mfr. #:: TPS2320IDR
설명:: Hot Swap Voltage Controllers 3-13V Dual w/Ind Chl Circuit Breaking
수명 주기:: 이 제조업체의 새 제품입니다.
데이터 시트:: TPS2320IDR 데이터 시트
배달:: DHL FedEx Ups TNT EMS
지불:: T/T Paypal Visa MoneyGram Western Union
ECAD Model:
추가 정보:: TPS2320IDR 추가 정보 TPS2320IDR Product Details

제품 속성
속성 값

제조사:: 텍사스 인스트루먼트

제품 카테고리:: 핫 스왑 전압 컨트롤러

RoHS:: Y

제품:: 컨트롤러 및 스위치

공급 전압 - 최대:: 13 V

공급 전압 - 최소:: 3 V

채널 수:: 2 Channel

작동 공급 전류:: 1 mA, 200 uA

최소 작동 온도:: - 40 C

최대 작동 온도:: + 85 C

장착 스타일:: SMD/SMT

패키지/케이스:: SOP-16

포장:: 릴

작동 온도 범위:: - 40 C to + 85 C

시리즈:: TPS2320

유형:: 양의 전압

상표:: 텍사스 인스트루먼트

작동 공급 전압:: 3 V to 13 V

상품 유형:: 핫 스왑 전압 컨트롤러

공장 팩 수량:: 2500

하위 카테고리:: PMIC - 전원 관리 IC

단위 무게:: 0.004998 oz

Tags: TPS2320ID, TPS2320I, TPS2320, TPS232, TPS23, TPS2, TPS

Service Guarantees

We guarantee 100% customer satisfaction.

Quality Guarantees

We provide 90-360 days warranty.

If the items you received were not in perfect quality, we would be responsible for your refund or replacement, but the items must be returned in their original condition.
Our experienced sales team and tech support team back our services to satisfy all our customers.

we buy and manage excess electronic components, including excess inventory identified for disposal.
Email us if you have excess stock to sell.

Email: [email protected]

Step1:
Vacuum Packaging with PL

Step2:
Anti-Static Bag

Step3:
Packaging Boxes

TPS2320IDR 평가 및 리뷰

F***a

I'm very satisfied

2019-06-01

D***r

2019-05-01

V***v

Annoying voice of chinese girl

2019-06-26

B***z

Perfect as always

2019-04-04

TPS2320IDR 설명

***as Instruments: 3-V to 13-V dual channel hot swap with active low enable 16-SOIC -40 to 85

***ical: Hot Swap Controller 2-CH 5.5V/13V N-Channel Positive Voltage 16-Pin SOIC T/R

*** Source Electronics: IC HOT SWAP CTRLR GP 16SOIC / DUAL HOT SWAP POWER CONTROLLERS WITH INDEPENDENT CIRCUIT BREAKER

***ser: Hot Swap and Power Distribution 3-13V Dual w/Ind Chl Circuit Breaking

***ark: Hot Swap Controller IC; Applications:Hot-Swap / Plug / Dock Power Management, Hot-Plug PCI, Device Bay, Electronic Circuit Breaker; Supply Voltage Range:3V to 13V; Digital IC Case Style:SOIC; No. of Pins:16 ;RoHS Compliant: Yes

***as Instruments: 3-13V Dual Hot-Swap IC w/ Independent Channel Circuit Breaking, Act-High Enable 16-SOIC -40 to 85

***et: Hot Swap Controller 2-CH 5.5V/13V 16-Pin SOIC T/R

***ser: Hot Swap and Power Distribution 3-13V Dual w/Ind Chl Circuit Breaking

***ark: Hot Swap Controller IC; Applications:Hot-Swap / Plug / Dock Power Management, Hot-Plug PCI, Device Bay, Electronic Circuit Breaker; Supply Voltage Range:3V to 13V; Digital IC Case Style:SOIC; No. of Pins:16 ;RoHS Compliant: Yes

***as Instruments: 3-V to 13-V dual channel hot swap with active high enable 16-SOIC -40 to 85

***ical: Hot Swap Controller 2-CH 5.5V/13V N-Channel Positive Voltage 16-Pin SOIC Tube

***ser: Hot Swap and Power Distribution 3-13V Dual w/Ind Chl Circuit Breaking

***ark: Hot Swap Controller IC; Applications:Hot-Swap / Plug / Dock Power Management, Hot-Plug PCI, Device Bay, Electronic Circuit Breaker; Supply Voltage Range:3V to 13V; Digital IC Case Style:SOIC; No. of Pins:16 ;RoHS Compliant: Yes

***ark: DUAL PROGRAMMABLE CURRENT LIMIT SINGLE HIGH-SIDE SWITCH 16 SOIC .150IN TUBE ROHS COMPLIANT: YES

*** Electronics: Current Limit SW 2-IN 2-OUT 2.7V to 5.5V 1.5A 16-Pin SOIC N

***rochip SCT: USB Power Dist, 2.7 to 5.5V, 80mΩ, SOIC-16, RoHS

*** Stop Electro: Buffer/Inverter Based Peripheral Driver, 2 Driver, 0.1A, PDSO16

***i-Key: IC PWR SWITCH N-CHAN 1:1 16SOIC

***ponent Stockers USA: 0.1 A BUF OR INV BASED PRPHL DRVR PDSO16

***or: DUAL PROGRAMABLE CURRENT LIMIT S

***ark: DUAL PROGRAMMABLE CURRENT LIMIT SINGLE HIGH-SIDE SWITCH 16 SOIC .150IN TUBE ROHS COMPLIANT: YES

*** Electronics: Current Limit SW 2-IN 2-OUT 2.7V to 5.5V 1.5A 16-Pin SOIC N

***rochip SCT: USB Power Dist, 2.7 to 5.5V, 80mΩ, SOIC-16, RoHS

*** Stop Electro: Buffer/Inverter Based Peripheral Driver, 0.1A, PDSO16

***i-Key: IC PWR SWITCH N-CHAN 1:1 16SOIC

***ure Electronics: MIC2546 Series 5.5 V 120 mOhm Dual Programmable Current Limit Switch - SOIC-16

***rochip: Dual Programmable Current Limit Single High-Side Switch

*** Electronics: Current Limit SW 2-IN 2-OUT 2.7V to 5.5V 1.5A 16-Pin SOIC N

***rochip SCT: USB Power Dist, 2.7 to 5.5V, 80mΩ, SOIC-16, RoHS

***ca Corp: Power Supply Support Circuit, Adjustable, 2 Channel, PDSO16

*** Stop Electro: Buffer/Inverter Based Peripheral Driver, 0.1A, PDSO16

***i-Key: IC PWR SWITCH N-CHAN 1:1 16SOIC

***ical: Current Limit SW 2-IN 2-OUT to 15A Automotive 16-Pin SOIC Tube

*** Electronic Components: Power Switch ICs - Power Distribution Double Ch High Side 36V VCC 65mOhm 9.5A

***et: MOSFET DRVR 6A 2-OUT Hi Side Non-Inv 16-Pin SOIC Tube

***icroelectronics: Double channel high-side driver

***ource: IC DRIVER HIGH SIDE 2CH 16-SOIC

***r Electronics: Buffer/Inverter Based Peripheral Driver

***i-Key: IC PWR DRIVER N-CHANNEL 1:1 16SO

***-Wing Technology: Tube VND830 Current Limiting (Fixed) Open Load Detect Over Temperature Over Voltage On/Off power distribution switch 36V 30mus 6A 8.3W

***AS INSTRUMENT: The TPS2320 and TPS2321 are dual-channel hot-swap controllers that use external N-channel MOSFETs as high-side switches in power applications. Features of these devices, such as overcurrent protection (OCP), inrush-current control, and the ability to discriminate between load transients and faults, are critical requirements for hot-swap applications.

***AS INSTRUM: The TPS2320/21 devices incorporate undervoltage lockout (UVLO) to ensure the device is off at startup. Each internal charge pump, capable of driving multiple MOSFETs, provides enough gate-drive voltage to fully enhance the N-channel MOSFETs. The charge pumps control both the rise times and fall times (dv/dt) of the MOSFETs, reducing power transients during power up/down. The circuit-breaker functionality combines the ability to sense overcurrent conditions with a timer function; this allows designs such as DSPs, that may have high peak currents during power-state transitions, to disregard transients for a programmable period.

***AS INSTRUMEN: DISCH1, DISCH2 – DISCH1 and DISCH2 should be connected to the sources of the external N-channel MOSFET transistors connected to GATE1 and GATE2, respectively. These pins discharge the loads when the MOSFET transistors are disabled. They also serve as reference-voltage connections for internal gate voltage-clamp circuitry.

***XS: ENABLE or ENABLE – ENABLE for TPS2320 is active low. ENABLE for TPS2321 is active high. When the controller is enabled, both GATE1 and GATE2 voltages will power up to turn on the external MOSFETs. When the ENABLE pin is pulled high for TPS2320 or the ENABLE pin is pulled low for TPS2321 for more than 50 µs, the gate of the MOSFET is discharged at a controlled rate by a current source, and a transistor is enabled to discharge the output bulk capacitance. In addition, the device turns on the internal regulator PREREG (see VREG) when enabled and shuts down PREREG when disabled so that total supply current is much less than 5µA.

***XS: FAULT – FAULT is an open-drain overcurrent flag output. When an overcurrent condition in either channel is sustained long enough to charge TIMER to 0.5 V, the overcurrent channel latches off and pulls FAULT low. The other channel will run normally if not in overcurrent. In order to turn the channel back on, either the enable pin has to be toggled or the input power has to be cycled.

***as Instruments (TI): GATE1, GATE2 – GATE1 and GATE2 connect to the gates of external N-channel MOSFET transistors. When the device is enabled, internal charge-pump circuitry pulls these pins up by sourcing approximately 15µA to each. The turnon slew rates depend upon the capacitance present at the GATE1 and GATE2 terminals. If desired, the turnon slew rates can be further reduced by connecting capacitors between these pins and ground. These capacitors also reduce inrush current and protect the device from false overcurrent triggering during power up. The charge-pump circuitry will generate gate-to-source voltages of 9 V-12 V across the external MOSFET transistors.

***AS INSRUMENTS: IN1, IN2 – IN1 and IN2 should be connected to the power sources driving the external N-channel MOSFET transistors connected to GATE1 and GATE2, respectively. The TPS2320/TPS2321 draws its operating current from IN1, and both channels will remain disabled until the IN1 power supply has been established. The IN1 channel has been constructed to support 3-V, 5-V, or 12-V operation, while the IN2 channel has been constructed to support 3-V or 5-V operation

***XS: ISENSE1, ISENSE2, ISET1, ISET2 – ISENSE1 and ISENSE2, in combination with ISET1 and ISET2, implement overcurrent sensing for GATE1 and GATE2. ISET1 and ISET2 set the magnitude of the current that generates an overcurrent fault, through external resistors connected to ISET1 and ISET2. An internal current source draws 50 µA from ISET1 and ISET2. With a sense resistor from IN1 to ISENSE1 or from IN2 to ISENSE2, which is also connected to the drains of external MOSFETs, the voltage on the sense resistor reflects the load current. An overcurrent condition is assumed to exist if ISENSE1 is pulled below ISET1 or if ISENSE2 is pulled below ISET2. To ensure proper circuit breaker operation, VI(ISENSE1) and VI(ISET1) should never exceed VI(IN1). Similarly, VI(ISENSE2) and VI(ISET2) should never exceed VI(IN2).

***AS INTRUMENTS: TIMER – A capacitor on TIMER sets the time during which the power switch can be in overcurrent before turning off. When the overcurrent protection circuits sense an excessive current, a current source is enabled which charges the capacitor on TIMER. Once the voltage on TIMER reaches approximately 0.5 V, the circuit-breaker latch is set and the power switch is latched off. Power must be recycled or the ENABLE pin must be toggled to restart the controller. In high-power or high-temperature applications, a minimum 50-pF capacitor is strongly recommended from TIMER to ground, to prevent any false triggering.

***INS: VREG – VREG is the output of an internal low-dropout voltage regulator, where IN1 is the input. The regulator is used to generate a regulated voltage source, less than 5.5 V, for the device. A 0.1-Î¼F ceramic capacitor should be connected between VREG and ground to aid in noise rejection. In this configuration, upon disabling the device, the internal low-dropout regulator will also be disabled, which removes power from the internal circuitry and allows the device to be placed in low-quiescent-current mode. In applications where IN1 is less than5.5 V, VREG and IN1 may be connected together. However, under these conditions, disabling the device will not place the device in low-quiescent-current mode, because the internal low-dropout voltage regulator is being bypassed, thereby keeping internal circuitry operational. If VREG and IN1 are connected together, a 0.1-µF ceramic capacitor between VREG and ground is not needed if IN1 already has a bypass capacitor of 1µF to 10µF.

Market price

부분 #	설명	재고	가격
TPS2320IDR DISTI # 31706327	Hot Swap Controller 2-CH 5.5V/13V N-Channel Positive Voltage 16-Pin SOIC T/R RoHS: Compliant	10000	5000:$1.8310 2500:$2.0563
TPS2320IDR DISTI # TPS2320IDR-ND	IC DUAL HOTSWAP PWR CONT 16-SOIC RoHS: Compliant Min Qty: 2500 Container: Tape & Reel (TR)	Temporarily Out of Stock	2500:$1.7556
TPS2320IDRG4 DISTI # TPS2320IDRG4-ND	IC DUAL HOTSWAP PWR CONT 16-SOIC RoHS: Compliant Min Qty: 2500 Container: Tape & Reel (TR)	Temporarily Out of Stock	2500:$1.7556
TPS2320IDR DISTI # V39:1801_07412616	Hot Swap Controller 2-CH 5.5V/13V N-Channel Positive Voltage 16-Pin SOIC T/R RoHS: Compliant	0
TPS2320IDRG4 DISTI # V39:1801_07412618	Hot Swap Controller 2-CH 5.5V/13V N-Channel Positive Voltage 16-Pin SOIC T/R RoHS: Compliant	0
TPS2320IDR DISTI # TPS2320IDR	Hot Swap Controller 2-CH 5.5V/13V 16-Pin SOIC T/R - Tape and Reel (Alt: TPS2320IDR) RoHS: Compliant Min Qty: 2500 Container: Reel	Americas - 0	2500:$1.8900 5000:$1.7900 10000:$1.6900 15000:$1.6900 25000:$1.5900
TPS2320IDR DISTI # TPS2320IDR	Hot Swap Controller 2-CH 5.5V/13V 16-Pin SOIC T/R (Alt: TPS2320IDR) RoHS: Compliant Min Qty: 2500 Container: Tape and Reel	Europe - 0	2500:€2.1900 5000:€1.8900 10000:€1.6900 15000:€1.6900 25000:€1.5900
TPS2320ID DISTI # 595-TPS2320ID	Hot Swap Voltage Controllers 3-13V Dual w/Ind Chl Circuit Breaking RoHS: Compliant	155	1:$4.1900 10:$3.7700 100:$3.0800 250:$2.8900 500:$2.6300 1000:$2.2100 2500:$2.1000
TPS2320IDR DISTI # 595-TPS2320IDR	Hot Swap Voltage Controllers 3-13V Dual w/Ind Chl Circuit Breaking RoHS: Compliant	0	1:$3.5000 10:$3.1400 100:$2.5700 250:$2.4100 500:$2.1900 1000:$1.8400 2500:$1.7500
TPS2320IDG4 DISTI # 595-TPS2320IDG4	Hot Swap Voltage Controllers 3-13V Dual w/Ind Chl Circuit Breaking RoHS: Compliant	0
TPS2320IDRG4 DISTI # 595-TPS2320IDRG4	Hot Swap Voltage Controllers 3-13V Dual w/Ind Chl Circuit Breaking RoHS: Compliant	0
TPS2320IDR	Power Supply Support Circuit, Adjustable, 2 Channel, PDSO16 RoHS: Compliant	10000	1000:$1.7400 500:$1.8300 100:$1.9000 25:$1.9900 1:$2.1400